Profi switch Dell Force10 S55T Show Command
30. dubna 2019Příkaz show je jedním z nejdůležitějších příkazů. Slouží k zobrazení konfigurace nebo přehledu různých informací. Tento článek je takovou příručkou a přehledem, co nám všchno tento příkaz umožňuje. Spousta výpisů je zkrácených.
Verze operačního systému
Force10#show version
Dell Force10 Networks Real Time Operating System Software
Dell Force10 Operating System Version: 1.0
Dell Force10 Application Software Version: 8.3.5.3
Copyright (c) 1999-2012 by Dell Inc. All Rights Reserved.
Build Time: Fri Nov 30 15:23:43 2012
Build Path: /sites/sjc/work/build/buildSpaces/build03/E8-3-5/SW/SRC
Force10 uptime is 6 day(s), 23 hour(s), 27 minute(s)
System image file is "system://A"
System Type: S55
Control Processor: Freescale MPC8536E with 2147483648 bytes of memory.
128M bytes of boot flash memory.
1 48-port E/FE/GE (SD)
48 GigabitEthernet/IEEE 802.3 interface(s)Systémové informace
Force10#show system
Stack MAC : 00:01:e8:8b:ae:f8
Reload Type : normal-reload [Next boot : normal-reload]
-- Unit 0 --
Unit Type : Management Unit
Status : online
Next Boot : online
Required Type : S55 - 48-port E/FE/GE (SD)
Current Type : S55 - 48-port E/FE/GE (SD)
Master priority : 0
Hardware Rev : 2.0
Num Ports : 52
Up Time : 6 day, 23 hr, 31 min
FTOS Version : 8.3.5.3
Jumbo Capable : yes
POE Capable : no
Burned In MAC : 00:01:e8:8b:ae:f8
No Of MACs : 3
...Force10#show os-version
RELEASE IMAGE INFORMATION :
---------------------------------------------------------------------
Platform Version Size ReleaseTime
S-Series: SD 8.3.5.3 21822632 Nov 30 2012 15:29:36
TARGET IMAGE INFORMATION :
---------------------------------------------------------------------
Type Version Target checksum
runtime 8.3.5.3 Control Processor passed
CPLD IMAGE INFORMATION :
---------------------------------------------------------------------
Card CPLD Name Version
Stack-unit 0 S55 SYSTEM CPLD 2Force10#show file-systems
Size(b) Free(b) Feature Type Flags Prefixes
2056916992 2056830976 FAT32 USERFLASH rw flash:
- - - network rw ftp:
- - - network rw tftp:
- - - network rw scp:Force10#show environment
-- Fan Status --
Unit Bay TrayStatus Fan0 Speed
--------------------------------------------------------------------------------
0 0 up up 8520
0 1 up up 8880
Speed in RPM
-- Power Supplies --
Unit Bay Status Type FanStatus
---------------------------------------------------------------------------
0 0 up AC good
0 1 absent absent or down
-- Unit Environment Status --
Unit Status Temp Voltage
---------------------------------------------------------------------------
* 0 online 39C ok
* Management Unit
-- Thermal Sensor Readings (deg C) --
Unit Sensor0 Sensor1
---------------------------
0 39 34Force10#show inventory
System Type : S55
System Mode : 1.0
Software Version : 8.3.5.3
Unit Type Serial Number Part Number Rev Piece Part ID Rev Svc Tag Exprs Svc Code
--------------------------------------------------------------------------------------------------------------
* 0 S55-01-GE-44T-AC GCDL135400115 7590009002 E CN-0TR7CT-28298-354-0115 A00 30RZTS1 657 736 819 3
0 S55-PWR-AC G6DL135400121 7590006902 A CN-0979K1-28298-354-0121 A00 N/A N/A
0 S55-FAN N/A N/A N/A N/A N/A N/A N/A
0 S55-FAN N/A N/A N/A N/A N/A N/A N/A
* - Management Unit
Software Protocol Configured
--------------------------------------------------------------Force10#show memory
Statistics On Unit 0 Processor
===========================
Total(b) Used(b) Free(b) Lowest(b) Largest(b)
2147483648 3112580 2144371068 2144354504 2144371068Zobrazení obsahu konfiguračních souborů
Force10#show running-config
Current Configuration ...
! Version 7.4.1.0
! Last configuration change at Tue Apr 10 17:43:38 2007 by admin
! Startup-config last updated at Thu Mar 29 02:35:08 2007 by default
!
boot system rpm0 primary flash://FTOS-EF-7.4.1.0.bin
boot system rpm0 secondary flash://FTOS-EF-6.3.1.2.bin
boot system rpm0 default flash://FTOS-EF-6.5.1.8.bin
!
...K zobrazení konfigurace při bootování systému slouží příkaz show startup-config.
Síťová rozhraní
Force10#show interfaces status
Port Description Status Speed Duplex Vlan
Gi 0/0 Down Auto Auto 1
Gi 0/1 Down Auto Auto 1
Gi 0/2 Up 1000 Mbit Full 1
Gi 0/3 Down Auto Auto 1
Gi 0/4 Up 10 Mbit Full 1
Gi 0/5 Down Auto Auto 1
...K podrobnějšímu výpisu slouží příkazy:
Force10#show interfaces gigabitethernet 0/0
Force10#show interfaces switchportForce10#show interfaces port-channel 1 brief
Codes: L - LACP Port-channel
LAG Mode Status Uptime Ports
L 1 L2 up 08:40:46 Gi 0/36 (Up)
Gi 0/37 (Up)Force10#show ip interface brief
Interface IP-Address OK Method Status Protocol
GigabitEthernet 0/0 unassigned NO Manual up down
GigabitEthernet 0/1 unassigned NO Manual up down
GigabitEthernet 0/2 unassigned YES Manual up up
GigabitEthernet 0/3 unassigned NO Manual up down
GigabitEthernet 0/4 10.10.10.1 YES Manual up up
...Force10#monitor interface gigabitethernet 0/2
Force10 uptime is 1 week(s), 0 day(s), 1 hour(s), 14 minute(s)
Monitor time: 00:00:00 Refresh Intvl.: 2s
Interface: Gi 0/2, Enabled, Link is Up, Linespeed is 1000 Mbit
Traffic statistics: Current Rate Delta
Input bytes: 107389685 0 Bps 0
Output bytes: 111402096 0 Bps 0
Input packets: 128523 0 pps 0
Output packets: 141923 0 pps 0
64B packets: 9694 0 pps 0
Over 64B packets: 11025 0 pps 0
Over 127B packets: 10475 0 pps 0
Over 255B packets: 956 0 pps 0
Over 511B packets: 160 0 pps 0
Over 1023B packets: 96213 0 pps 0
Error statistics:
Input underruns: 0 0 pps 0
Input giants: 0 0 pps 0
Input throttles: 0 0 pps 0
Input CRC: 0 0 pps 0
Input IP checksum: 0 0 pps 0
Input overrun: 0 0 pps 0
Output underruns: 0 0 pps 0
Output throttles: 0 0 pps 0
m - Change mode c - Clear screen
l - Page up a - Page down
T - Increase refresh interval t - Decrease refresh interval
q - QuitTabulka MAC adres
Force10#show mac-address-table
VlanId Mac Address Type Interface State
1 00:01:0c:01:0d:06 Dynamic Gi 0/13 Active
1 00:05:01:01:07:00 Dynamic Po 1 Active
1 00:09:08:0e:07:01 Dynamic Po 1 Active
1 00:05:09:0c:06:30 Dynamic Gi 0/43 ActiveDalší příkazy:
Force10#show mac-address-table vlan 10
Force10#show mac-address-table count
Force10#show mac-address-table aging-timeVLAN
Force10#show vlan
Codes: * - Default VLAN, G - GVRP VLANs, P - Primary, C - Community, I - Isolated
Q: U - Untagged, T - Tagged
x - Dot1x untagged, X - Dot1x tagged
G - GVRP tagged, M - Vlan-stack, H - VSN tagged
i - Internal untagged, I - Internal tagged
NUM Status Description Q Ports
* 1 Active U Po1(Gi 0/36-37)
U Po2()
U Gi 0/0-17,24-35,38-43
10 Inactive "NAS Server" T Gi 0/21
U Gi 0/18-20Force10#show interfaces vlan 10
Vlan 10 is down, line protocol is down
Description: "NAS Server"
Address is 00:01:e8:8b:ae:fa, Current address is 00:01:e8:8b:ae:fa
Interface index is 1107787786
Internet address is 192.168.10.254/24
MTU 1554 bytes, IP MTU 1500 bytes
LineSpeed auto
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters 1w0d0h
Queueing strategy: fifo
Time since last interface status change: 1w0d0hForce10#show vlan brief
VLAN Name STG MAC Aging IP Address
---- -------------------------------- ---- --------- ------------------
1 0 1800 unassigned
10 0 1800 192.168.10.254/24Zobrazení času
Force10#show calendar
16:33:30 UTC Mon Jun 26 2017
Force10#show clock detail
11:05:56.949 UTC Mon Jun 26 2017
Time source is RTC hardwareV případě, že máte nakonfigurováno NTP, potom se hodí příkazy:
Force10#show ntp associations
remote ref clock st when poll reach delay offset disp
==========================================================================
78.108.102.237 0.0.0.0 16 - 16 0 0.00 0.000 16000.0
*82.113.53.40 0.0.0.0 16 - 16 0 -0.08 -1499.9 16000.0
89.221.212.46 0.0.0.0 16 - 16 0 0.00 0.000 16000.0
147.231.100.5 0.0.0.0 16 - 16 0 0.00 0.000 16000.0
* master (synced), # master (unsynced), + selected, - candidateForce10#show ntp status
Clock is synchronized, stratum 2, reference is 100.10.10.10
frequency is -32.000 ppm, stability is 15.156 ppm, precision is 4294967290
reference time is BC242FD5.C7C5C000 (10:15:49.780 UTC Mon Jan 10 2000)
clock offset is clock offset msec, root delay is 0.01656 sec
root dispersion is 0.39694 sec, peer dispersion is peer dispersion msec
peer mode is clientSeznam výše uvedených příkazů není úplný, switch toho umí zobrazit podstatně víc. Zájemci nechť prostudují dokumentaci na webu dellu.